string(0) ""

string trimmer spools

Spools Guide - Find the right spool for your string trimmer

sort by
Page 1 From 5

Cutting line spools and replacement spools for strimmers, scythes and brushcutters

Reliably trim your grass and cut your lawn where your lawn mower cannot reach: Strimmers, scythes and brushcutters

If the spool is empty, IKRA have original replacement cutting line spools. Simply keep a stock of replacement spools to prevent interruption. This prevents the inconvenience of having the spool run out right in the middle of strimming and there being no spool at hand to replace it with.

Simply replace the spool and carry on. Practical: The cordless strimmer IAT 40-3025 LI has an integrated compartment for the spare spool!

There are specially-priced economy packs of three in the IKRA online shop. You save ca. 33%. So, you buy two spools and get one free in the economy pack. Maintaining a stock pays off. It is good for your wallet and your lawn can continue to be reliably trimmed.

You can also find spools for older IKRA tools in the shop.

  • Test

    Order the replacement spool DA-F13 in a set of 3 and save 31% in...

    €33.99
  • Hint! String Trimmer Replacement Spools DA-C1 (3-Pack)

    Order the replacement spool DA-C1 in a set of 3 and save 31% in...

    €34.99
  • Hint! String Trimmer Replacement Spools DA-F17 (3-Pack)

    Original replacement spool for IKRA string trimmers and brush cutters...

    €34.99
  • Hint! String Trimmer Replacement Spools DA-F16 (3-Pack)

    Order the replacement spool DA-F16 in a set of 3 and save 31% in...

    €49.99
  • String Trimmer Replacement Spool DEA (2-Pack)

    Original replacement spool for IKRA string trimmers and brush cutters...

    €13.99
  • String Trimmer Replacement Spool DA-F13

    Original replacement spool for IKRA string trimmers and brush cutters...

    €16.49
  • String Trimmer Replacement Spool DA-F16

    Original replacement spool for IKRA string trimmers and brush cutters...

    €24.29
  • String Trimmer Replacement Spool DA-F17

    Original replacement spool for IKRA string trimmers and brush cutters...

    €24.29
  • String Trimmer Replacement Spool DA-C1

    Original replacement spool for IKRA string trimmers and brush cutters...

    €16.99
  • Hint! String Trimmer Replacement Spools DA-S (3-Pack)

    Order the replacement spool DA-S in a set of 3 and save 33% in...

    €17.99
  • String Trimmer Replacement Spool DA-S

    Original replacement spool for IKRA string trimmers and brush cutters...

    €8.99
  • Hint! String Trimmer Replacement Spools DA-S3 (3-Pack)

    Order the replacement spool DA-S3 in a set of 3 and save 33% in...

    €24.99
sort by
Page 1 From 5

Cutting line spools - Original replacement spools from IKRA

Worth knowing about replacement spools for strimmers:

Strimming line feed

There are three different methods for feeding out the cutting line on the trimming heads. On the one hand, the semi-automatic cutting line feed, the so-called automatic tapping feed. Here, the cutting line is fed out by briefly "tapping" the strimming head on the ground. (e.g. with spools DA, DA-F1 to DA-F17, etc.) This system is used by most IKRA strimmers. In the case of the fully automatic line adjustment, the nylon cutting line is fed out automatically without having to tap the strimmer on the ground. (e.g. with spools DV, DV-S, VA/1 and VA/2) With the BK, M and S cutting line spools, the cutting line must be drawn out manually.

Adjusting the strimming line with automatic tapping feed

If there is a reduction in cutting performance, the cutting line must be lengthened. Tap the feed button lightly on the ground while the motor is running. Do not press the feed button against the ground for an extended period of time. Centrifugal force and the brief tapping of the spool head on the ground causes a small amount of the cutting line to be fed off the spool and "drawn out". The cutting line trimming blade on the protective cover will trim the cutting line to the correct length. In order to prevent the cutting line becoming tangled, tap only once on the ground to lengthen the cutting line. If more cutting line is required, wait a few seconds before tapping the feed button on the ground again. Ensure that the length of the cutting line always matches the mowing diameter, or is close to this.

If the line is shorter than 2.5 cm, it must be readjusted manually. To do so, switch the device off, unplug the power plug and turn it over. Press the knob on the cutting line spool until the stop is reached and pull on the end of the cutting line. If there is no cutting line visible at all, replace the cutting line spool with a new spool. When replacing the cutting line spool, always follow the operating instructions for your IKRA strimmer, your scythe or your brushcutter.

Sppol for Lawn Edger

Difference between single cutting line spools & double cutting line spools

There are cutting line cartridges with one cutting line and cutting line cartridges with two cutting lines. So, in the case of the single cutting line spool, only one line rotates to cut the grass. With double cutting line spools, two nylon lines rotate to cut the grass. Single cutting line spools from IKRA include the following spools, for example: A, BK, M and S. However, most replacement cutting line spools from IKRA are double cutting line spools, e.g. DA, DA-F1 - DA-F17, DV, VA/2, etc. The double cutting line head ensures particularly efficient lawn trimming.

Thickness of the nylon cutting line

The thickness of the nylon cutting line varies as it is used in different tools. Cutting line spools for strimmers generally have somewhat thinner threads. The thickness here is ca. 1.00 - 1.60 mm (e.g. spools DA, D, BK, A, AC, M, S, etc.). Grass at edges and corners, e.g. at wall and fences, can be reliably trimmed. The line thickness for scythes and brushcutters is ca. 2.00 - 2.50 mm (e.g. DA-F12, DA-F8, DA-F4 & DA-F5, etc.) and so is the thicker variant. Scythes and brushcutters also have a special undergrowth cutter for dealing with brush and undergrowth. This can be simply swapped with the cutting line spool. Nylon line often comes into contact with walls and fences but will not damage them. However, you should ideally try to avoid the cutting line coming into contact with hard objects, such as wood and stone, as this will use up the cutting line faster.

Whisper lines / quiet lines

Whisper lines are rotating strimming lines with special "notching", which reduces the noise level db (A). All whisper lines from IKRA are identified accordingly on the article pages. The following cutting line spools from IKRA are manufactured in this way: DV, DEA, DA-C1, DA-F13, DV-S & VA/2

Operation and construction of strimming heads

The cutting line spools contain a sturdy plastic line (nylon line), in various lengths, which is wound onto a spring in the interior of the spool. As soon as the strimmer starts and the strimming head rotates, centrifugal force accelerates the cutting line outwards. The high rotational speed causes the nylon line to cut through the grass blades like a whip. This ensures a precision cut and a uniform final result.

40 Volt Cordless Lawn Edger